Precision PT100 RTD and thermocouple sensors engineered for bearing temperature monitoring in electric motors, gearboxes, turbines, and industrial rotating equipment. Flat-pack, push-in, and embedded designs. AS9100D certified manufacture with full documentation packages.
Bearing failure is the leading cause of motor and gearbox downtime. Temperature rise above baseline operating conditions is the earliest and most reliable indicator of impending failure — preceding vibration anomalies and acoustic emission by 6 to 72 hours in most failure modes.
Continuous bearing temperature monitoring enables condition-based maintenance, eliminates scheduled downtime from unnecessary preventive replacement, and provides the data needed to characterize lubrication adequacy, misalignment, overloading, and contamination — before catastrophic failure occurs.
Sensor geometry is determined by bearing type, housing design, and access constraints. All designs maintain electrical isolation from bearing race and housing to prevent ground loop interference with monitoring instrumentation.
Custom dimensions, connector types, lead lengths, and sheath materials available on all configurations. Contact engineering for application-specific designs.
Both sensing technologies are used in bearing monitoring. Selection depends on temperature range, accuracy requirements, wiring constraints, and EMI environment.
| Parameter | PT100 RTD (4-Wire) | Type K Thermocouple |
|---|---|---|
| Accuracy (at 100°C) | ±0.35°C (Class A) | ±1.5–2.5°C (Class 1–2) |
| Long-Term Stability | Excellent — <0.1°C/year drift | Moderate — susceptible to decalibration |
| Temperature Range | –200°C to +600°C | –200°C to +1260°C |
| Response Time (flat-pack) | 2–10 sec typical | 1–5 sec typical |
| EMI/RFI Rejection | Excellent (low resistance, 4W) | Fair — requires shielded extension |
| Wiring Complexity | 3 or 4 conductors required | 2 conductors (matched alloy) |
| Lead Wire Cost | Copper — low cost | KX alloy extension — higher cost |
| Cold Junction Compensation | Not required | Required at instrument |
| Recommended Use | Standard bearing monitoring (most applications) | High-temp or fast-response applications |
For most electric motor and gearbox bearing monitoring applications, PT100 RTD in 3-wire configuration with Class A element is the standard recommendation. Thermocouple sensors are selected where bearing operating temperature may exceed 300°C or where sub-second response is required.
The values below are general industry reference points. Actual alarm setpoints must be established from baseline commissioning data for the specific machine and operating conditions. Both absolute temperature and rate-of-rise (ΔT/Δt) alarms are recommended.
| Bearing/Machine Type | Normal Operating Range | Warning Threshold | Alarm / Trip | Notes |
|---|---|---|---|---|
| Anti-friction (rolling element) — standard electric motor | 40–80°C (housing) | 90°C or +20°C above baseline | 100°C or +30°C above baseline | IEC 60034-14 guidance; absolute threshold varies with grease rating |
| Sleeve / journal bearing — general industrial | 50–80°C (babbitt) | 90–100°C babbitt | 110°C babbitt | Babbitt metal temp limit; alarm at 105–110°C common practice |
| High-speed turbine journal bearing | 60–90°C (white metal) | 100°C | 110–120°C (emergency trip) | API 670 provides specific setpoint methodology for rotating machinery protection |
| Aerospace motor / actuator bearing | Defined by motor spec | Trating − 20°C | Trating − 10°C | Grease thermal rating governs; often 125°C or 150°C rated grease |
| Gearbox bearing — rate-of-rise alarm | Stable ±2°C | +5°C in 15 minutes | +10°C in 15 minutes | Rate-of-rise alarm independent of absolute value — early fault indicator |
Source: IEC 60034-14, API 670, ISO 13373. These values are for reference only. Consult OEM documentation and establish baseline for each specific machine installation.
Technical questions about bearing temperature sensor selection, installation, and calibration. Contact our engineering team for application-specific guidance.
Request a Quote